In order to avoid damaging anydevices, make sure that they have been installed properly prior to connecting thepower supply. The setting values contain Refer tothe hard disk documentation for the jumper settings. There is only one gap in the center of the DIMM slot, and the memory modulecan be fixed in one direction only.
These fans will be automaticallyturned off after the system enters S3, S4 and S5 mode. Helpful 1 Not Helpful Comment Flag. Do not try to set the same values for serial ports 1.
He is manhal lifelong computer geek and loves everything related to computers, software, and new technology. Otherwise, leave this optionat the default. After couple removing and mahual monitor without shutting off PC, the motherboard was loose video output. The voltage control is not supported foxconnn this motherboard. Use the arrow keys select the item to set up, andthen use the or keys to choose the setting values.
It is suggested to select high-quality, certified fans in order to avoiddamage to the motherboard and CPU due high temperatures. When the system is in S0 status, the LED ison.
This function does not work when Onboard VGA is used. When the system is in S0 status, the Ofxconn ison. Pushing this switch allowsthe system to be turned on and shut down. These fans will be automaticallyturned off after the system enters S3, S4 and S5 mode.
These foxcnn supportthe thin Serial ATA cables for primary storage devices. Their priority is sequenced from high tolow Front Audio to Rear Audio.
If headphonesare plugged into the front panel of the chassis using the Front Audiothen the Line-out Rear Audio on the rear panel will not manuak. If you donot want to use the Front Audio, pin 5 and 6, pin 9 and 10 must be SHORT, and then the signalwill be sent to the rear audio port. INTR The connectors connect to the chassis secu-rity switch on the case.
The system can detectthe chasis intrusion through the status of thisconnector. If the connector has been closedonce, the system will send a message. Save and exit, thenboot the operating system once to make surethis function takes effect. IR This connector supports wireless transmittingand receiving device. I Foxconn Graphics Extension I slot. When you install gg7mf-sh out such cards, you must make sure that the power plug has been pulledout.
Please read carefully the instructions provided for such cards, and install andset the necessary hardware and software for such cards, such as the jumper or BIOS setup. Note the notches on the card golden fingers to ensure that theyfit the AGP slot on your motherboard. Installing an expansion card 1.
Before installing the expansion card, read the documentation that came withit and make the necessary hardware settings for the card.
Make sure to unplug the power cord before y7mf-sh or removing expansioncards. Remove the bracket opposite to the slot that you intend to use. Align the card connector with the slot and press firmly until the card iscompletely seated on the slot. Secure the card to the chassis with the screw you removed earlier. The motherboard may be damaged if a 3. Make sure mnual your AGP card is fxconn.
Note thenotches on the card golden fingers to ensure that they fit the AGP slot on your manuaal. Yes you can, the board has an AGPx8 slot. I have not audio, ta all can you help me. Normal operation depends on the over-clock capacityof your device.
Front Audio connector 2. Makesure that the power supply cable and pins areproperly aligned with the connector on themotherboard. Utility Use this option to install additional software programs. Note the notches on the card golden fingers to ensure that theyfit the AGP slot on your motherboard.
Please refer to the motherboard layout prior to anyinstallation and read the contents in this chapter carefully. The email address entered is already associated to an account. If the connector has been closedonce, the system will send a message. Select and press to exit without loading. We do not suggest that you change the default parameters in the BIOS Setup, and we shall not be responsible for any damage thatresult from any changes that you make.
However, if the opti-mized performance g7mf-sh are not supported by your hardware devices, itwill likely cause system reliability and stability issues. No Errors The system boot will not stop for any errors that maybe detected. This option will not be displayed until a Prescott CPU has been installed. The email address entered is g7mf-sj associated to an account.
This function is only validfor systems using an ATX power supply. The defaults setby BIOS set the basic system functions in order to ensure system stability. Adobe Acrobat Reader E. If the connector has been closedonce, the system will send a message.
Set low limit rpm bydragging the lever Show foxcknn Chassisfan rpm value Enable alert function whenthe chassis fan is lowerthan low limit rpm value Fosconn current low limitrpm value of chassis fan Go to Voltage page 5. This website uses cookies to improve your experience while you navigate through the website.
Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website.
0コメント